@anasluqman089

I have finished modelling and the hinge system.

Almost ready for submitting for funding

I have refined the design a bit but Im still continuing the locking mechanism

Devlog #7 Hello everyone! One of the staff has given me recommendations to change how the locker lock itself. I will now use hinges and tomorrow I will put a locking mechanism using the servo

Devlog #4 Hello everyone! The 3D is finished! I added a hole for the USB-C and the SD card. Created the lid and the half circle is for the keychain. that is all for today and I will submit it for funding very soon!

Devlog #3 Hello everyone! Today, I have have put the button upside down and shorten the PCB a bit. Im continuing on with 3D model and as you can see the corner is rounded to reduce force on impact. That is all from me today.

*Devlog #4 Hello everyone! Today I have finished the 3D model and I will submit to funding later.

Devlog #6 Hello everyone! Today I want to explain something about the phone section. The lid that is disconnected from the phone locker will be connected to the servo, so the servo can open it and close it. Then, the wire of the servo will go under the support and throught the hole and connected to the PCB. Finally, the phone locker section is connected to the alarm section. This means the alarm section and the phone locker section will be printed together but if the 3D printer printing margins is to small, the alarm section and the locker section will be printed separatedly and be glued by using a 3D pen but it will not looked as good. so that is all from me and also follow along my other projects.

Devlog 2 Hello everyone! today I have edited the PCB to fit all the parts so this is just a short devlog

Devlog 1 Hello everyone! Yesterday I was doomscrolling then I found a post about a Kodak keychain camera and i want to build it, I will be using a XIAO ESP32-S3 Sense, 3x 6mm pushbutton and a 1.3” IPS LCD screen .It will be powered with a Li-Po battery. I have finished the schematic and the PCB design need some tweak. so follow along my project even thought there are other project that I haven’t finished but I have submitted Blare Phone Locker for funding so also follow that project too!

Devlog 3 Hello everyone I have finished the PCB and will continue with CAD. I added BME280 just for fun

Devlog #5 Hello everyone today I continue on building the 3D model. There is a hole for the wire to connect to the servo. The locker is almost ready but I need to add the support for the servo and the lid but there is something bugging me. How should the alarm and the locker be connected? That is all for me see you again~~~~

Devlog 2 : continued building the PCB

DEVLOG #4 Hello everyone today I continued on building the 3D model but I decided to make the 3D model of the alarm and the phone locker separate, It so confusing using OnShape for me but I managed. As you can see below, thats the alarm. It only take 2 AND A HALF HOUR but it look so horrible but I will continue.

Devlog 1 Hello everyone I decided that doing Blare Phone Locker everyday is boring so I decided to continue on another project. This is GlitchPad It contain an ESP32, a buzzer, an OLED screen, rotary encoder and 5 button. I’m planning the OLED screen will show the matrix like that cool number falling down or whatever and everytime you click the button the buzzer will buzz and for the rotary encoder……. Idk but I will continue tomorrow. The picture below show the schematic

Devlog #3 Hello everyone, today I have flipped the connection pin for the display and servo motor so it will be an easier connection. I continued on building the 3D model but it took me 1 HOUR just to understand how 3D modelling work and another 1 HOUR for the first sketch but i I continued but I did my sketch wrong and as you can see the model below it is incomplete but I will continue tomorrow. Finally, I will be using a 500 mah Li-Po battery for the power sources. That is all for today

Quick Question Should I made it battery powered or usb powered

Devlog #2 Hello everyone, so I realized I need to change the PCB so I decided to edit it. At first, I edit the old PCB with the new part but it got very messy because THERE ARE TOO MANY TRACES. I NEED TO PUT SO MANY HOLE but then, I realized I can redo it. So I redo it but THERE IS STILL TOO MANY TRACESSSSS. It was tiring but the new PCB have a vertical pin for the servo. Then I continue with CAD and it was very confusing, I keep rotating SO MUCH. Tomorrow I can’t continue because I’m going to vacation but my STREAKKK gonna enddd . So that’s all for today and give me your advice

Devlog 1 : First time using the software so it took me 2 hours just to do the basic thing but I will continue