Having problem with studying due to playing phone? Look no further, Blare Phone Locker is like your normal alarm but with a twist it have a compartment that you can put your phone and it automatically close for the desired hour
@anasluqman089
on
Blare Phone Locker
17m 1s logged
I have finished modelling and the hinge system.
@anasluqman089
on
Blare Phone Locker
50m 1s logged
Almost ready for submitting for funding
@anasluqman089
on
Blare Phone Locker
38m 1s logged
I have refined the design a bit but Im still continuing the locking mechanism
@anasluqman089
on
Blare Phone Locker
1h 50m 3s logged
Devlog #7 Hello everyone! One of the staff has given me recommendations to change how the locker lock itself. I will now use hinges and tomorrow I will put a locking mechanism using the servo
@anasluqman089
on
Blare Phone Locker
18m 22s logged
Devlog #6 Hello everyone! Today I want to explain something about the phone section. The lid that is disconnected from the phone locker will be connected to the servo, so the servo can open it and close it. Then, the wire of the servo will go under the support and throught the hole and connected to the PCB. Finally, the phone locker section is connected to the alarm section. This means the alarm section and the phone locker section will be printed together but if the 3D printer printing margins is to small, the alarm section and the locker section will be printed separatedly and be glued by using a 3D pen but it will not looked as good. so that is all from me and also follow along my other projects.
@anasluqman089
on
Blare Phone Locker
2h 19m 30s logged
Devlog #5 Hello everyone today I continue on building the 3D model. There is a hole for the wire to connect to the servo. The locker is almost ready but I need to add the support for the servo and the lid but there is something bugging me. How should the alarm and the locker be connected? That is all for me see you again~~~~
@anasluqman089
on
Blare Phone Locker
3h 0m 46s logged
DEVLOG #4 Hello everyone today I continued on building the 3D model but I decided to make the 3D model of the alarm and the phone locker separate, It so confusing using OnShape for me but I managed. As you can see below, thats the alarm. It only take 2 AND A HALF HOUR but it look so horrible but I will continue.
@anasluqman089
on
Blare Phone Locker
2h 39m 28s logged
Devlog #3 Hello everyone, today I have flipped the connection pin for the display and servo motor so it will be an easier connection. I continued on building the 3D model but it took me 1 HOUR just to understand how 3D modelling work and another 1 HOUR for the first sketch but i I continued but I did my sketch wrong and as you can see the model below it is incomplete but I will continue tomorrow. Finally, I will be using a 500 mah Li-Po battery for the power sources. That is all for today
@anasluqman089
on
Blare Phone Locker
32m 20s logged
Quick Question Should I made it battery powered or usb powered
@anasluqman089
on
Blare Phone Locker
3h 4m 36s logged
Devlog #2 Hello everyone, so I realized I need to change the PCB so I decided to edit it. At first, I edit the old PCB with the new part but it got very messy because THERE ARE TOO MANY TRACES. I NEED TO PUT SO MANY HOLE but then, I realized I can redo it. So I redo it but THERE IS STILL TOO MANY TRACESSSSS. It was tiring but the new PCB have a vertical pin for the servo. Then I continue with CAD and it was very confusing, I keep rotating SO MUCH. Tomorrow I can’t continue because I’m going to vacation but my STREAKKK gonna enddd . So that’s all for today and give me your advice
@anasluqman089
on
Blare Phone Locker
2h 13m 55s logged
Devlog 1 : First time using the software so it took me 2 hours just to do the basic thing but I will continue
