You are browsing as a guest. Sign up (or log in) to start making projects!

apricity

@apricity

Joined October 6th, 2026

  • 2Devlogs
  • 1Projects
  • 0Ships
  • 0Votes
Open comments for this post

3h 24m 2s logged

10/31: Finishing PCB and case. My goals were to finish wiring the new PCB (with the larger screen and adding a battery connector) and to design a 3D printable case with cutouts for buttons at the top (to keep the depth of the case lower). I selected a 420 mAh LiPo battery because the ESP32S3 Plus’ onboard charging circuit and battery pins were designed for a LiPo battery (with the added benefit of them being thinner than Alkalines). Additionally, 420 mAh happened to be the largest size Adafruit currently has in stock with a short connector. So, I spent some time trying to optimize the battery connector placement so that it wouldn’t get stabbed by pins or conflict with other parts, and wouldn’t put too much strain on the cable. Next, I finished up the wiring and started on the case before realizing that the PCB was lopsided around the screen, so I had to shrink the height so it would look good and rewire the keyswitches (it also took an embarrassingly long amount of time for me to realize that the keyswitch footprint was incorrect which was why the 3D model wouldn’t sync up, had to go and look at an older project to realize.) Once the 2nd iteration was finished, I imported it into Onshape and designed a case (PCB held on by screw holes into the acrylic). I had to create a model of the screen I was using because there were no existing ones, and designed a top to be superglued on (in order to make it easier to put the keyswitches on top). There is a port to charge the battery of USB-C, so I shouldn’t need to open the case.

0
0
7
Open comments for this post

2h 39m 42s logged

Basic PCB Setup: starting off as individualizing the guide for BLARE (alarm clock guided project) just to get a sense of the size I want the project to be. My goal for this project is to create a small, portable alarm clock that is more consistent than my current one, can store music as .wav files, and has some method of getting me awake more effectively (current plan is to make the only way to turn off the alarm to solve definite integrals). I finished the schematic and wired up the keyswitches, pin header, and buzzer to the esp32c3. Additionally, I finished wiring the PCB. I chose to switch to a rectangular form factor considering I would want to carry this for travel and it needs to be as thin as possible. The next steps are to adapt it to the items I currently have and decide what extra features I would like (also to add a battery) 10/30, proceeding with further customizing the alarm clock. I currently have a 2.8” TFT display that I ordered before realizing that it was the wrong size for another project, so I plan on using it (it also conveniently supports touchscreen!) The larger screen will help with displaying more info (if I want weather, etc.), has a better color range so it looks better, and also has an SD card slot if I want to store data (can also display and store more math problems!). The TFT does however have 18 pins (14 for the display and 4 for the SD card), which the ESP32C3 I was using cannot handle. So, I switched to a ESP32S3 Plus because it has more pins, and decided to drop the 5 pins for the touchscreen so I could wire it to the ESP32. With regards to form factor, the case will only be slightly larger than the screen, and the buttons are either going to be mounted on the back or on the top of the case (the latter requires wires to be soldered to the board, which could come out after much jostling and bumping). Tasks completed: switching out the ESP32C3 for a ESP32S3, rewiring schematic to new MCU and adding 14 pin and 4 pin header for the new display, redesigning board and moving around components, and rewiring PCB. I switched to 3 buttons instead of four due to space constraints (currently planning on soldering wires to buttons on the top of the case). To do: need to write some basic firmware, add in a battery/power solution, and make a case.

0
0
20

Followers

Loading…